/**
  @page ADC_DualMode ADC Dual Mode Description
  
  @verbatim
  ******************** (C) COPYRIGHT 2012 STMicroelectronics *******************
  * @file    ADC/ADC_DualMode/readme.txt 
  * @author  MCD Application Team
  * @version V1.0.0
  * @date    23-October-2012
  * @brief   ADC Dual Mode Example Description.
  ******************************************************************************
  *
  * Licensed under MCD-ST Liberty SW License Agreement V2, (the "License");
  * You may not use this file except in compliance with the License.
  * You may obtain a copy of the License at:
  *
  *        http://www.st.com/software_license_agreement_liberty_v2
  *
  * Unless required by applicable law or agreed to in writing, software 
  * distributed under the License is distributed on an "AS IS" BASIS, 
  * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
  * See the License for the specific language governing permissions and
  * limitations under the License.
  *   
  ******************************************************************************
   @endverbatim

@par Example Description 

This example provides a short description of how to use the ADC peripheral to
convert a regular channel in Dual interleaved mode using the DMA to read 
the converted Data from the commun DR register.
Detailed steps of ADC1 and ADC2 configuration are provided starting from GPIO configuration
to the analog channel configuration without forgetting the ADC1 and ADC2 calibration procedure. 
 
In this example the shared input ADC12 Channel7(PC1) is used for ADC1 and ADC2.
ADC12 Channel7(PC1) is directly connected to the potentiometer(RV2) available on 
the STM32303C-EVAL evaluation board. 

The converted voltage is displayed on the onboard LCD.

@par Directory contents 

  - ADC/ADC_DualMode/stm32f30x_conf.h    Library Configuration file
  - ADC/ADC_DualMode/stm32f30x_it.c      Interrupt handlers
  - ADC/ADC_DualMode/stm32f30x_it.h      Interrupt handlers header file
  - ADC/ADC_DualMode/main.c              Main program
  - ADC/ADC_DualMode/main.h              Main program header file
  - ADC/ADC_DualMode/system_stm32f30x.c  STM32F30x system source file
  
@note The "system_stm32f30x.c" is generated by an automatic clock configuration 
      system and can be easily customized to your own configuration. 
      To select different clock setup, use the "STM32F30x_Clock_Configuration_V1.0.0.xls" 
      provided with the AN4152 package available on <a href="http://www.st.com/internet/mcu/family/141.jsp">  ST Microcontrollers </a>
         
@par Hardware and Software environment

  - This example runs on STM32F30x Devices.
  
  - This example has been tested with STMicroelectronics STM32303C-EVAL RevB (STM32F30x)
    evaluation board and can be easily tailored to any other supported device 
    and development board.
    
  - STM32303C-EVAL Set-up
    - RV2 Potentiometer connected to PC.01 pin.
    - Make sure that the jumper JP11 and JP12 is fitted.
    - Make sure that the jumper JP15 and JP17 are fitted in 3V3 position.


@par How to use it ? 

In order to make the program work, you must do the following :
 - Copy all source files from this example folder to the template folder under
   Project\STM32F30x_StdPeriph_Templates
 - Open your preferred toolchain 
 - Rebuild all files and load your image into target memory
 - Run the example
    
 * <h3><center>&copy; COPYRIGHT STMicroelectronics</center></h3>
 */
