/*****************************************************
This program was produced by the
CodeWizardAVR V2.03.9 Standard
Automatic Program Generator
© Copyright 1998-2008 Pavel Haiduc, HP InfoTech s.r.l.
http://www.hpinfotech.com

Project : 
Version : 
Date    : 06.03.2010
Author  : Admin
Company : Microsoft
Comments: 


Chip type               : ATtiny2313
AVR Core Clock frequency: 8,000000 MHz
Memory model            : Tiny
External RAM size       : 0
Data Stack size         : 32
*****************************************************/

#include <tiny2313.h>
#include <delay.h>

#define MAX_DS18b20 2

// 1 Wire Bus functions
#asm
   .equ __w1_port=0x12 ;PORTD
   .equ __w1_bit=0
#endasm
#include <1wire.h>
#include <ds18b20.h>  

int OutDigit = 0;
int g_i = 1;

void DisplayTemp(int tempr);

// Timer 0 output compare A interrupt service routine
interrupt [TIM0_COMPA] void timer0_compa_isr(void)
{
    // Place your code here
//    TCNT0=0x00;
//    DisplayTemp(OutDigit);    

}

// Timer 1 output compare A interrupt service routine
interrupt [TIM1_COMPA] void timer1_compa_isr(void)
{
// Place your code here
//    DisplayTemp(OutDigit);
}


// Declare your global variables here

//цифры
const char numbers[] = 
{
    0b00101000,  //0
    0b11101110,  //1
    0b00110010,  //2
    0b10100010,  //3
    0b11100100,  //4
    0b10100001,  //5
    0b00100001,  //6
    0b11101010,  //7
    0b00100000,  //8
    0b10100000,  //9
    0b11011111,  // - точка
    0b11111111  // пусто
};

void TurnOnDisplay(char iNum, char iDig, char dot)
{
    char q = 1;          
    char d = numbers[iDig]; 

    PORTD.4 = 3 == iNum;
    PORTD.5 = 2 == iNum;
    PORTD.6 = 1 == iNum;
             
    PORTB = d;
    delay_us(300);

    if(dot)
    {         
        PORTB = numbers[10];
    }

//    PORTD.4 = 0;
//    PORTD.5 = 0;
//    PORTD.6 = 0;
}

void DisplayTemp(int tempr)
{
    //последная цифра
    char a1 = tempr%10;
    char s = sizeof(tempr); 
    TurnOnDisplay(1, a1, 0);
                     
    //средня
    tempr /= 10;
    a1 = tempr%10;
    TurnOnDisplay(2, a1, 1);

    //первая
    tempr /= 10;
    a1 = tempr%10;
    TurnOnDisplay(3, a1, 0);

    PORTD.4 = 0;
    PORTD.5 = 0;
    PORTD.6 = 0;    
}


void main(void)
{
// Declare your local variables here
int temp = 1;


// Crystal Oscillator division factor: 1
#pragma optsize-
CLKPR=0x80;
CLKPR=0x00;
#ifdef _OPTIMIZE_SIZE_
#pragma optsize+
#endif

// Input/Output Ports initialization
// Port A initialization
// Func2=In Func1=In Func0=In 
// State2=T State1=P State0=P 
PORTA=0x03;
DDRA=0x00;

// Port B initialization
// Func7=Out Func6=Out Func5=Out Func4=Out Func3=Out Func2=Out Func1=Out Func0=Out 
// State7=0 State6=0 State5=0 State4=0 State3=0 State2=0 State1=0 State0=0 
PORTB=0x00;
DDRB=0xFF;

// Port D initialization
// Func6=Out Func5=Out Func4=Out Func3=Out Func2=Out Func1=Out Func0=Out 
// State6=1 State5=1 State4=1 State3=0 State2=0 State1=0 State0=0 
PORTD=0x00;
DDRD=0x7F;

// Timer/Counter 0 initialization
// Clock source: System Clock
// Clock value: 31,250 kHz
// Mode: CTC top=OCR0A
// OC0A output: Disconnected
// OC0B output: Disconnected
TCCR0A=0x02;
TCCR0B=0x01;
TCNT0=0x00;
OCR0A=0xFF;
OCR0B=0x00;

// Timer/Counter 1 initialization
// Clock source: System Clock
// Clock value: Timer 1 Stopped
// Mode: Normal top=FFFFh
// OC1A output: Discon.
// OC1B output: Discon.
// Noise Canceler: Off
// Input Capture on Falling Edge
// Timer 1 Overflow Interrupt: Off
// Input Capture Interrupt: Off
// Compare A Match Interrupt: Off
// Compare B Match Interrupt: Off
TCCR1A=0x00;
TCCR1B=0x0D;
TCNT1H=0x00;
TCNT1L=0x00;
ICR1H=0x00;
ICR1L=0x00;
OCR1AH=0x00;
OCR1AL=0xD0;
OCR1BH=0x00;
OCR1BL=0x00;

// External Interrupt(s) initialization
// INT0: Off
// INT1: Off
// Interrupt on any change on pins PCINT0-7: Off
GIMSK=0x00;
MCUCR=0x00;

// Timer(s)/Counter(s) Interrupt(s) initialization
TIMSK=0x00;

// Universal Serial Interface initialization
// Mode: Disabled
// Clock source: Register & Counter=no clk.
// USI Counter Overflow Interrupt: Off
USICR=0x00;

// Analog Comparator initialization
// Analog Comparator: Off
// Analog Comparator Input Capture by Timer/Counter 1: Off
ACSR=0x80;

// 1 Wire Bus initialization
w1_init();

while (1)
      {          
      
            g_i++;
            if(g_i > 2000)
            {     
                g_i = 0;
                OutDigit++;            
           }
      
          
            DisplayTemp(OutDigit);

      };
}
