
avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.26rev3 (Oct 31 2008 14:01:29)  http://www.ln.ua/~real/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command: +attiny26 -aa -p1 -o0,8 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.09us
	% Atmel adapter for STK*00 found
	% STK mode
	% osc = 0kHz -> XTAL will be generated
	% with SCK low 16 periods, high 16 periods
	% Reset
	% PgmOn reply  FF FE 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% ReadLock command  58 00 00 00
	% ReadLock reply    00 58 00 FF
Chip not locked
	% ReadOsccal command  38 00 00 00
	% ReadOsccal reply    00 38 00 9B
	% ReadOsccal command  38 00 01 00
	% ReadOsccal reply    00 38 00 9E
	% ReadOsccal command  38 00 02 00
	% ReadOsccal reply    00 38 00 93
	% ReadOsccal command  38 00 03 00
	% ReadOsccal reply    00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FE 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% ReadLock command  58 00 00 00
	% ReadLock reply    00 58 00 FF
	% ReadFuses command  50 00 00 00
	% ReadFuses reply    00 50 00 AF
	% ReadFuses command  58 08 00 00
	% ReadFuses reply    00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (4.6s)
Verifying CODE memory
... passed
 done (4.2s)
Total time 9.2s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.26rev3 (Oct 31 2008 14:01:29)  http://www.ln.ua/~real/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command: +attiny26 -aa -p1 -o0,8 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.09us
	% Atmel adapter for STK*00 found
	% STK mode
	% osc = 0kHz -> XTAL will be generated
	% with SCK low 16 periods, high 16 periods
	% Reset
	% PgmOn reply  FF FE 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% ReadLock command  58 00 00 00
	% ReadLock reply    00 58 00 FF
Chip not locked
	% ReadOsccal command  38 00 00 00
	% ReadOsccal reply    00 38 00 9B
	% ReadOsccal command  38 00 01 00
	% ReadOsccal reply    00 38 00 9E
	% ReadOsccal command  38 00 02 00
	% ReadOsccal reply    00 38 00 93
	% ReadOsccal command  38 00 03 00
	% ReadOsccal reply    00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FE 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% ReadLock command  58 00 00 00
	% ReadLock reply    00 58 00 FF
	% ReadFuses command  50 00 00 00
	% ReadFuses reply    00 50 00 AF
	% ReadFuses command  58 08 00 00
	% ReadFuses reply    00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (4.5s)
Verifying CODE memory
... passed
 done (4.1s)
Total time 9.1s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0,8 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.29us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 16 periods, high 16 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF FF FF
	% Try 1 to resync by reset pulse	% PgmOn reply  FF FF FF FF
	% Try 2 to resync by reset pulse	% PgmOn reply  FF FF FF FF
	% Try 3 to resync by reset pulse	% PgmOn reply  FF FF FF FF
	% Try 4 to resync by reset pulse	% PgmOn reply  FF FF FF FF
Can't resync

Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0,8 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 16 periods, high 16 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FE 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FE 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (5.9s)
Verifying CODE memory

	% Verifying from 0x0 to 0x7CF  ... passed
 done (5.4s)
Total time 11.8s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.29us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (1.08s)
Verifying CODE memory

	% Verifying from 0x0 to 0x7B3  ... passed
 done (0.72s)
Total time 2.24s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (1.08s)
Verifying CODE memory

	% Verifying from 0x0 to 0x7B3  ... passed
 done (0.72s)
Total time 2.24s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (1.12s)
Verifying CODE memory

	% Verifying from 0x0 to 0x7FD  ... passed
 done (0.76s)
Total time 2.32s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.29us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (1.12s)
Verifying CODE memory

	% Verifying from 0x0 to 0x7F9  ... passed
 done (0.76s)
Total time 2.32s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.29us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (1.12s)
Verifying CODE memory

	% Verifying from 0x0 to 0x7FB  ... passed
 done (0.76s)
Total time 2.32s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (1.12s)
Verifying CODE memory

	% Verifying from 0x0 to 0x7F7  ... passed
 done (0.76s)
Total time 2.32s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
.... done (1.12s)
Verifying CODE memory

	% Verifying from 0x0 to 0x7FF  .... passed
 done (0.76s)
Total time 2.33s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
.... done (1.12s)
Verifying CODE memory

	% Verifying from 0x0 to 0x7FF  .... passed
 done (0.76s)
Total time 2.33s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
.... done (1.12s)
Verifying CODE memory

	% Verifying from 0x0 to 0x7FF  .... passed
 done (0.75s)
Total time 2.35s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (1.00s)
Verifying CODE memory

	% Verifying from 0x0 to 0x725  ... passed
 done (0.67s)
Total time 2.12s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (0.99s)
Verifying CODE memory

	% Verifying from 0x0 to 0x71D  ... passed
 done (0.67s)
Total time 2.11s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (0.99s)
Verifying CODE memory

	% Verifying from 0x0 to 0x71D  ... passed
 done (0.67s)
Total time 2.11s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (0.99s)
Verifying CODE memory

	% Verifying from 0x0 to 0x71D  ... passed
 done (0.67s)
Total time 2.11s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (0.99s)
Verifying CODE memory

	% Verifying from 0x0 to 0x71D  ... passed
 done (0.67s)
Total time 2.11s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (0.99s)
Verifying CODE memory

	% Verifying from 0x0 to 0x71D  ... passed
 done (0.67s)
Total time 2.11s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.31us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.38MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (1.00s)
Verifying CODE memory

	% Verifying from 0x0 to 0x71D  ... passed
 done (0.68s)
Total time 2.12s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
.... done (1.12s)
Verifying CODE memory

	% Verifying from 0x0 to 0x7FF  .... passed
 done (0.76s)
Total time 2.32s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (1.12s)
Verifying CODE memory

	% Verifying from 0x0 to 0x7FD  ... passed
 done (0.76s)
Total time 2.32s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (1.11s)
Verifying CODE memory

	% Verifying from 0x0 to 0x7FB  ... passed
 done (0.75s)
Total time 2.31s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (1.12s)
Verifying CODE memory

	% Verifying from 0x0 to 0x7F7  ... passed
 done (0.75s)
Total time 2.31s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (1.11s)
Verifying CODE memory

	% Verifying from 0x0 to 0x7FB  ... passed
 done (0.75s)
Total time 2.31s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (1.13s)
Verifying CODE memory

	% Verifying from 0x0 to 0x7F7  ... passed
 done (0.76s)
Total time 2.33s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (1.12s)
Verifying CODE memory

	% Verifying from 0x0 to 0x7F9  ... passed
 done (0.76s)
Total time 2.32s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
.... done (1.12s)
Verifying CODE memory

	% Verifying from 0x0 to 0x7FF  .... passed
 done (0.76s)
Total time 2.33s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (1.12s)
Verifying CODE memory

	% Verifying from 0x0 to 0x7F3  ... passed
 done (0.75s)
Total time 2.32s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (1.12s)
Verifying CODE memory

	% Verifying from 0x0 to 0x7EF  ... passed
 done (0.75s)
Total time 2.31s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (1.11s)
Verifying CODE memory

	% Verifying from 0x0 to 0x7E9  ... passed
 done (0.75s)
Total time 2.31s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (1.12s)
Verifying CODE memory

	% Verifying from 0x0 to 0x7E7  ... passed
 done (0.75s)
Total time 2.31s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (1.11s)
Verifying CODE memory

	% Verifying from 0x0 to 0x7E7  ... passed
 done (0.75s)
Total time 2.31s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (1.11s)
Verifying CODE memory

	% Verifying from 0x0 to 0x7E7  ... passed
 done (0.75s)
Total time 2.31s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (1.12s)
Verifying CODE memory

	% Verifying from 0x0 to 0x7ED  ... passed
 done (0.76s)
Total time 2.32s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (1.12s)
Verifying CODE memory

	% Verifying from 0x0 to 0x7F1  ... passed
 done (0.76s)
Total time 2.32s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (1.12s)
Verifying CODE memory

	% Verifying from 0x0 to 0x7F3  ... passed
 done (0.76s)
Total time 2.32s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (1.12s)
Verifying CODE memory

	% Verifying from 0x0 to 0x7F1  ... passed
 done (0.75s)
Total time 2.32s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (1.12s)
Verifying CODE memory

	% Verifying from 0x0 to 0x7F3  ... passed
 done (0.76s)
Total time 2.32s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (1.12s)
Verifying CODE memory

	% Verifying from 0x0 to 0x7FD  ... passed
 done (0.76s)
Total time 2.32s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
.... done (1.13s)
Verifying CODE memory

	% Verifying from 0x0 to 0x7FF  .... passed
 done (0.76s)
Total time 2.33s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (1.12s)
Verifying CODE memory

	% Verifying from 0x0 to 0x7FD  ... passed
 done (0.76s)
Total time 2.32s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (1.11s)
Verifying CODE memory

	% Verifying from 0x0 to 0x7FD  ... passed
 done (0.75s)
Total time 2.31s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (1.12s)
Verifying CODE memory

	% Verifying from 0x0 to 0x7FD  ... passed
 done (0.75s)
Total time 2.31s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (1.12s)
Verifying CODE memory

	% Verifying from 0x0 to 0x7F9  ... passed
 done (0.75s)
Total time 2.31s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (1.10s)
Verifying CODE memory

	% Verifying from 0x0 to 0x7DD  ... passed
 done (0.74s)
Total time 2.29s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (1.10s)
Verifying CODE memory

	% Verifying from 0x0 to 0x7DD  ... passed
 done (0.74s)
Total time 2.29s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.38MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (1.12s)
Verifying CODE memory

	% Verifying from 0x0 to 0x7E9  ... passed
 done (0.75s)
Total time 2.31s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.29us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (1.17s)
Verifying CODE memory

	% Verifying from 0x0 to 0x7E3  ... passed
 done (0.77s)
Total time 2.39s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.29us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (1.05s)
Verifying CODE memory

	% Verifying from 0x0 to 0x711  ... passed
 done (0.69s)
Total time 2.19s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.29us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (1.06s)
Verifying CODE memory

	% Verifying from 0x0 to 0x721  ... passed
 done (0.69s)
Total time 2.19s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -e -fCKOPT=1,CKSEL=F -w -v -% -c tiny26.hex
	% Fuse added: CKOPT=1
	% Fuse added: CKSEL=F
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.29us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% MCU osc frequency = 800kHz
	% setup 2.50us, hold 2.50us
	% actual spi IO frequency 155kHz
Adapter enabled
	% Reset
	% PgmOn reply  FF FE 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 BB
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 BB
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 B4
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 B5
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FE 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 E1
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= BB BB B4 B5
_LOW = 0xE1
  PLLCK     	= 1
  CKOPT     	= 1
  SUT       	= 2
  CKSEL     	= 1
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (0.69s)
Verifying CODE memory

	% Verifying from 0x0 to 0x721  ... passed
 done (0.37s)
Programming fuses
	% Write Fuses	command AC A0 00 EF,  reply 00 AC A0 00
	% Read Fuses	command 50 00 00 00,  reply EF 50 00 EF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
New fuses value
  OSCCALs	= BB BB B4 B5
_LOW = 0xEF
  PLLCK     	= 1
  CKOPT     	= 1
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Verifying fuses
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 EF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
passed
Total time 1.53s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -e -fCKOPT=0,CKSEL=F -w -v -% -c tiny26.hex
	% Fuse added: CKOPT=0
	% Fuse added: CKSEL=F
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.29us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% MCU osc frequency = 800kHz
	% setup 2.50us, hold 2.50us
	% actual spi IO frequency 155kHz
Adapter enabled
	% Reset
	% PgmOn reply  FF FE 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 BB
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 BB
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 B4
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 B5
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FE 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 EF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= BB BB B4 B5
_LOW = 0xEF
  PLLCK     	= 1
  CKOPT     	= 1
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (0.68s)
Verifying CODE memory

	% Verifying from 0x0 to 0x721  ... passed
 done (0.37s)
Programming fuses
	% Write Fuses	command AC A0 00 AF,  reply 00 AC A0 00
	% Read Fuses	command 50 00 00 00,  reply AF 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
New fuses value
  OSCCALs	= BB BB B4 B5
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Verifying fuses
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
passed
Total time 1.53s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (1.08s)
Verifying CODE memory

	% Verifying from 0x0 to 0x70D  ... passed
 done (0.74s)
Total time 2.26s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.38MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (1.06s)
Verifying CODE memory

	% Verifying from 0x0 to 0x70D  ... passed
 done (0.70s)
Total time 2.21s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (1.08s)
Verifying CODE memory

	% Verifying from 0x0 to 0x711  ... passed
 done (0.69s)
Total time 2.21s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (1.08s)
Verifying CODE memory

	% Verifying from 0x0 to 0x721  ... passed
 done (0.72s)
Total time 2.25s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (1.05s)
Verifying CODE memory

	% Verifying from 0x0 to 0x71F  ... passed
 done (0.71s)
Total time 2.20s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.38MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (1.08s)
Verifying CODE memory

	% Verifying from 0x0 to 0x71F  ... passed
 done (0.71s)
Total time 2.24s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.29us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (1.06s)
Verifying CODE memory

	% Verifying from 0x0 to 0x723  ... passed
 done (0.70s)
Total time 2.21s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.29us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (1.08s)
Verifying CODE memory

	% Verifying from 0x0 to 0x777  ... passed
 done (0.74s)
Total time 2.27s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF FF FF
	% Try 1 to resync by reset pulse	% PgmOn reply  FF FF FF FF
	% Try 2 to resync by reset pulse	% PgmOn reply  FF FF FF FF
	% Try 3 to resync by reset pulse	% PgmOn reply  FF FF FF FF
	% Try 4 to resync by reset pulse	% PgmOn reply  FF FF FF FF
Can't resync

Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (1.13s)
Verifying CODE memory

	% Verifying from 0x0 to 0x777  ... passed
 done (0.73s)
Total time 2.30s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (1.09s)
Verifying CODE memory

	% Verifying from 0x0 to 0x763  ... passed
 done (0.73s)
Total time 2.27s
Reset pin released
Adapter disabled

avreal/WIN32  -  AVR controllers LPT programmer by Redchuk Alexandr
v1.27r4 (Oct  6 2009 16:12:37)  http://real.kiev.ua/avreal
bug-reports, suggestions and so on mail to avreal@real.kiev.ua
Command:
  +attiny26 -aa -p1 -o0 -e -w -v -% -c tiny26.hex
	% LPT port number 1
	% LPT base address 0x378
	% DLportIO.dll succesfully loaded, DLportIO.sys interface activated
	% LPT write cycle 1.30us
	% Atmel adapter for STK*00 found
	% STK adapter mode
	% 0.39MHz XTAL will be generated
	% with SCK low 2 periods, high 2 periods
Adapter enabled
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
Chip not locked
	% Read Osccal	command 38 00 00 00,  reply 00 38 00 9B
	% Read Osccal	command 38 00 01 00,  reply 00 38 00 9E
	% Read Osccal	command 38 00 02 00,  reply 00 38 00 93
	% Read Osccal	command 38 00 03 00,  reply 00 38 00 98
	% Erase reply  00 AC 80 00
Device erased
	% Reset
	% PgmOn reply  FF FF 53 00
	% Synchronised after 1 try
	% GetID reply  00 30 00 1E
	% GetID reply  00 30 00 91
	% GetID reply  00 30 00 09
	% Read ID: 0x1E9109
Device connected, tiny26 detected
	% Read Lock	command 58 00 00 00,  reply 00 58 00 FF
	% Read Fuses	command 50 00 00 00,  reply 00 50 00 AF
	% Read Fuses	command 58 08 00 00,  reply 00 58 08 F7
Fuses 
  OSCCALs	= 9B 9E 93 98
_LOW = 0xAF
  PLLCK     	= 1
  CKOPT     	= 0
  SUT       	= 2
  CKSEL     	= F
_HIGH = 0xF7
  RSTDISBL  	= 1
  EESAVE    	= 1
  BODLEVEL  	= 1
  BODEN     	= 1
Programming CODE memory
... done (1.12s)
Verifying CODE memory

	% Verifying from 0x0 to 0x763  ... passed
 done (0.72s)
Total time 2.28s
Reset pin released
Adapter disabled
