я уже разобрался, в прерывание сую дать сигнал на порт С5, то когда клавишу жму лампочка загорается( диод т.е)
Код: Выделить всё
/*****************************************************
This program was produced by the
CodeWizardAVR V2.04.4a Advanced
Automatic Program Generator
© Copyright 1998-2009 Pavel Haiduc, HP InfoTech s.r.l.
<a href="http://www.hpinfotech.com">http://www.hpinfotech.com</a>
Project :
Version :
Date : 12/26/2011
Author :
Company :
Comments:
Chip type : ATmega8535
Program type : Application
AVR Core Clock frequency: 8.000000 MHz
Memory model : Small
External RAM size : 0
Data Stack size : 128
*****************************************************/
#include <mega8535.h>
#include <delay.h>
// Standard Input/Output functions
#include <stdio.h>
#define KBD_DATA PIND.3
// External Interrupt 0 service routine
unsigned char data,bitcount=11; // holds the received scan code
// keyboard scan codes (without & with shift key pressed)
flash unsigned char unshifted[67][2] = {
//0x0d,9,
0x0e,'`',0x15,'q',0x16,'1',0x1a,'z',0x1b,'s',0x1c,'a',0x1d,'w',0x1e,'2',0x21,'c',0x22,'x',0x23,'d',0x24,'e',
0x25,'4',0x26,'3',0x29,' ',0x2a,'v',0x2b,'f',0x2c,'t',0x2d,'r',0x2e,'5',0x31,'n',0x32,'b',0x33,'h',0x34,'g',
0x35,'y',0x36,'6',0x39,',',0x3a,'m',0x3b,'j',0x3c,'u',0x3d,'7',0x3e,'8',0x41,',',0x42,'k',0x43,'i',0x44,'o',
0x45,'0',0x46,'9',0x49,'.',0x4a,'/',0x4b,'l',0x4c,';',0x4d,'p',0x4e,'-',0x52,'`',0x54,'[',0x55,'=',0x5a,13,
0x5b,']',0x5d,'/',0x61,'<',0x66,8, 0x69,'1',0x6b,'4',0x6c,'7',0x70,'0',0x71,',',0x72,'2',0x73,'5',0x74,'6',
0x75,'8',0x79,'+',0x7a,'3',0x7b,'-',0x7c,'*',0x7d,'9',0,0 };
flash unsigned char shifted[67][2] = {
//0x0d,9,
0x0e,'`',0x15,'Q',0x16,'!',0x1a,'Z',0x1b,'S',0x1c,'A',0x1d,'W',0x1e,'C',0x22,'X',0x23,'D',0x24,'E',
0x25,'$',0x26,'#',0x29,' ',0x2a,'V',0x2b,'F',0x2c,'T',0x2d,'R',0x2e,'%',0x31,'N',0x32,'B',0x33,'H',0x34,'G',
0x35,'Y',0x36,'^',0x39,'L',0x3a,'M',0x3b,'J',0x3c,'U',0x3d,'&',0x3e,'*',0x41,'<',0x42,'K',0x43,'I',0x44,'O',
0x45,')',0x46,'(',0x49,'>',0x4a,'?',0x4b,'L',0x4c,':',0x4d,'P',0x4e,'_',0x52,'"',0x54,'{',0x55,'+',0x5a,13,
0x5b,'}',0x5d,'|',0x61,'>',0x66,8, 0x69,'1',0x6b,'4',0x6c,'7',0x70,'0',0x71,',',0x72,'2',0x73,'5',0x74,'6',
0x75,'8',0x79,'+',0x7a,'3',0x7b,'-',0x7c,'*',0x7d,'9',0,0 };
//***********************************************
// decode scan code
void decode(unsigned char sc) {
static unsigned char is_up=0, shift = 0, mode = 0;
unsigned char i;
if (!is_up) {
switch (sc) {
case 0xF0 :// The up-key identifier
is_up = 1;
break;
case 0x12 :// Left SHIFT
shift = 1;
break;
case 0x59 :// Right SHIFT
shift = 1;
break;
case 0x05 :// F1
if(mode == 0)
mode = 1;// Enter scan code mode
if(mode == 2)
mode = 3;// Leave scan code mode
break;
default:
if(mode == 0 || mode == 3) {// If ASCII mode
if(!shift) {// If shift not pressed, do a table look-up
for(i = 0; unshifted[i][0]!=sc && unshifted[i][0]; i++);
if (unshifted[i][0] == sc) {
putchar(unshifted[i][1]);
}
}
else {// If shift pressed
for(i = 0; shifted[i][0]!=sc && shifted[i][0]; i++);
if (shifted[i][0] == sc) {
putchar(shifted[i][1]);
}
}
}
else putchar(sc); // scan code mode (debugging mode)
break;
}
}
else {
is_up = 0;// Two 0xF0 in a row not allowed
switch (sc) {
case 0x12 :// Left SHIFT
shift = 0;
break;
case 0x59 :// Right SHIFT
shift = 0;
break;
case 0x05 :// F1 -- F1 puts you in debugging mode
// pressing F1 again gets you out of debugging mode
// in debugging mode hex code of the scan codes
// are stored in the buffer instead of their ascii codes
if(mode == 1)
mode = 2;
if(mode == 3)
mode = 0;
break;
}
}
}
//***********************************************
interrupt [EXT_INT0] void ext_int0_isr(void)
{
// Place your code here
// function entered at falling edge of the kbd clock signal
// if data bit is the next bit to be read
// (bit 3 to 10 is data, start, stop & parity bis are ignored
if((bitcount < 11) && (bitcount > 2)) {
data = (data >> 1);
if (KBD_DATA==1) // if next bit is 1
data = data | 0x80; // store a '1'
else
data = data & 0x7f; // else store a '0'
}
if(--bitcount == 0) { // all bits received ?
decode(data); // decode received byte
bitcount = 11; // reset bit counter
}
}
#ifndef RXB8
#define RXB8 1
#endif
#ifndef TXB8
#define TXB8 0
#endif
#ifndef UPE
#define UPE 2
#endif
#ifndef DOR
#define DOR 3
#endif
#ifndef FE
#define FE 4
#endif
#ifndef UDRE
#define UDRE 5
#endif
#ifndef RXC
#define RXC 7
#endif
#define FRAMING_ERROR (1<<FE)
#define PARITY_ERROR (1<<UPE)
#define DATA_OVERRUN (1<<DOR)
#define DATA_REGISTER_EMPTY (1<<UDRE)
#define RX_COMPLETE (1<<RXC)
// USART Receiver buffer
#define RX_BUFFER_SIZE 8
char rx_buffer[RX_BUFFER_SIZE];
#if RX_BUFFER_SIZE<256
unsigned char rx_wr_index,rx_rd_index,rx_counter;
#else
unsigned int rx_wr_index,rx_rd_index,rx_counter;
#endif
// This flag is set on USART Receiver buffer overflow
bit rx_buffer_overflow;
// USART Receiver interrupt service routine
interrupt [USART_RXC] void usart_rx_isr(void)
{
char status,data;
status=UCSRA;
data=UDR;
if ((status & (FRAMING_ERROR | PARITY_ERROR | DATA_OVERRUN))==0)
{
rx_buffer[rx_wr_index]=data;
if (++rx_wr_index == RX_BUFFER_SIZE) rx_wr_index=0;
if (++rx_counter == RX_BUFFER_SIZE)
{
rx_counter=0;
rx_buffer_overflow=1;
};
};
}
#ifndef _DEBUG_TERMINAL_IO_
// Get a character from the USART Receiver buffer
#define _ALTERNATE_GETCHAR_
#pragma used+
char getchar(void)
{
char data;
while (rx_counter==0);
data=rx_buffer[rx_rd_index];
if (++rx_rd_index == RX_BUFFER_SIZE) rx_rd_index=0;
#asm("cli")
--rx_counter;
#asm("sei")
return data;
}
#pragma used-
#endif
char ss;
void main(void)
{
// Declare your local variables here
// Input/Output Ports initialization
// Port A initialization
// Func7=In Func6=In Func5=In Func4=In Func3=In Func2=In Func1=In Func0=In
// State7=T State6=T State5=T State4=T State3=T State2=T State1=T State0=T
PORTA=0x00;
DDRA=0x00;
// Port B initialization
// Func7=In Func6=In Func5=In Func4=In Func3=In Func2=In Func1=In Func0=In
// State7=T State6=T State5=T State4=T State3=T State2=T State1=T State0=T
PORTB=0x00;
DDRB=0x00;
// Port C initialization
// Func7=In Func6=In Func5=In Func4=In Func3=In Func2=In Func1=In Func0=In
// State7=T State6=T State5=T State4=T State3=T State2=T State1=T State0=T
PORTC=0x00;
DDRC=0x00;
// Port D initialization
// Func7=In Func6=In Func5=In Func4=In Func3=In Func2=In Func1=In Func0=In
// State7=T State6=T State5=T State4=T State3=T State2=T State1=T State0=T
PORTD=0x00;
DDRD=0x00;
// Timer/Counter 0 initialization
// Clock source: System Clock
// Clock value: Timer 0 Stopped
// Mode: Normal top=FFh
// OC0 output: Disconnected
TCCR0=0x00;
TCNT0=0x00;
OCR0=0x00;
// Timer/Counter 1 initialization
// Clock source: System Clock
// Clock value: Timer1 Stopped
// Mode: Normal top=FFFFh
// OC1A output: Discon.
// OC1B output: Discon.
// Noise Canceler: Off
// Input Capture on Falling Edge
// Timer1 Overflow Interrupt: Off
// Input Capture Interrupt: Off
// Compare A Match Interrupt: Off
// Compare B Match Interrupt: Off
TCCR1A=0x00;
TCCR1B=0x00;
TCNT1H=0x00;
TCNT1L=0x00;
ICR1H=0x00;
ICR1L=0x00;
OCR1AH=0x00;
OCR1AL=0x00;
OCR1BH=0x00;
OCR1BL=0x00;
// Timer/Counter 2 initialization
// Clock source: System Clock
// Clock value: Timer2 Stopped
// Mode: Normal top=FFh
// OC2 output: Disconnected
ASSR=0x00;
TCCR2=0x00;
TCNT2=0x00;
OCR2=0x00;
// External Interrupt(s) initialization
// INT0: On
// INT0 Mode: Falling Edge
// INT1: Off
// INT2: Off
GICR|=0x40;
MCUCR=0x02;
MCUCSR=0x00;
GIFR=0x40;
// Timer(s)/Counter(s) Interrupt(s) initialization
TIMSK=0x00;
// USART initialization
// Communication Parameters: 8 Data, 1 Stop, No Parity
// USART Receiver: On
// USART Transmitter: On
// USART Mode: Asynchronous
// USART Baud Rate: 9600
UCSRA=0x00;
UCSRB=0x98;
UCSRC=0x86;
UBRRH=0x00;
UBRRL=0x33;
// Analog Comparator initialization
// Analog Comparator: Off
// Analog Comparator Input Capture by Timer/Counter 1: Off
ACSR=0x80;
SFIOR=0x00;
// Global enable interrupts
#asm("sei")
while (1)
{
if(getchar()){
DDRC = 0xff;
PORTC.5 = 0xFF;
}
};
}
даже отрицание ! поставить сигнала не будет и диод не будет гореть.... как мне сделать?
